{"product_id":"aem-v3-water-methanol-injection-kit-35psi-boost-dependent-controller-w-1-15-gallon-tank","title":"AEM V3 Water\/Methanol Injection Kit - 35psi Boost-Dependent Controller w\/ 1.15 Gallon Tank","description":"\u003cp\u003e\u003cstrong\u003eIN STOCK\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFits:\u003c\/strong\u003e Universal: forced-induction gasoline engines, up to 35 psi boost.\u003c\/p\u003e\n\u003ch2\u003eWhat this is\u003c\/h2\u003e\n\u003cp\u003eThe AEM V3 Water\/Methanol Injection Kit is a complete boost-dependent system for forced-induction engines, built around a controller with an internal MAP sensor rated up to 35 psi. It includes a compact 1.15-gallon reservoir with an anti-starvation design and integrated conductive fluid-level sensor, a 200 psi pump, three interchangeable jets (250, 500 and 1000 cc\/min) and 20 ft of nylon tubing, plus an LED status and low-fluid warning light.\u003c\/p\u003e\n\u003cp\u003eInjecting a water\/methanol mix cools the intake charge and suppresses knock, allowing more aggressive timing and boost.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0276\/1359\/3623\/files\/aem30-3300.jpg?v=1793669285\" alt=\"AEM V3 water\/methanol injection kit: 1.15 gallon tank with level sensor, pump, boost-dependent controller with wiring harness, nylon tubing and fittings\" loading=\"lazy\" width=\"420\" height=\"369\" style=\"max-width: 100%; height: auto; display: block; margin: 16px auto;\"\u003e\u003c\/p\u003e\n\u003ch2\u003eDesign\u003c\/h2\u003e\n\u003cp\u003eThe controller reads boost through its on-board MAP sensor, rated up to 35 psi, with a molded-in barbed nipple for the boost hose, and injects progressively: more boost, more fluid. Two large, turn-resistant knobs set where injection starts and where it reaches full flow; AEM's instructions give the Start PSI dial a range of 1 to 11 psig and the Full PSI dial 5 to 35 psig. The status LED and test button are covered for splash resistance, and the fuse is built into the controller housing.\u003c\/p\u003e\n\u003cp\u003eAEM's Boost Safe failsafe output activates on a short, loss of continuity, high or low voltage or a low fluid condition, so you can set up anything from a warning light to pulling boost or ignition timing, or switching fuel maps on a standalone engine management system. The kit has one machined billet injector with an integral check valve to prevent unintended flow, and a recirculation-style pump with integral fittings for quiet operation. The harness has a positive-lock connector, color-coded wires, an integrated pump ground circuit and an extra wire for an optional on\/off flow solenoid.\u003c\/p\u003e\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eV3 boost-dependent controller, internal MAP up to 35 psi\u003c\/li\u003e\n\u003cli\u003e1.15 gallon reservoir with conductive fluid level sensor\u003c\/li\u003e\n\u003cli\u003e200 psi water\/methanol pump\u003c\/li\u003e\n\u003cli\u003eIncludes 250, 500 \u0026amp; 1000 cc\/min jets\u003c\/li\u003e\n\u003cli\u003e20 ft nylon tubing\u003c\/li\u003e\n\u003cli\u003eSystem-status \/ low-fluid LED\u003c\/li\u003e\n\u003cli\u003eBoost Safe failsafe output\u003c\/li\u003e\n\u003cli\u003eTank dimensions (AEM): 10 in high x 8.5 in wide x 4.25 in deep\u003c\/li\u003e\n\u003cli\u003eAlso in the kit (AEM): 12 ft wiring harness, cockpit LED, vacuum hose and 1\/8 in tee fitting for the boost pickup, and mounting hardware\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eInstallation notes\u003c\/h2\u003e\n\u003cp\u003eAEM's instructions: mount the tank below the injection point and the nozzle above the tank, so fluid cannot leak into the intake tract through gravity or siphoning. The nozzle must go before the throttle plate, after the MAF sensor if there is one, and after any intercoolers; in most instances 6-8 in ahead of the throttle body gives an excellent combination of charge air cooling and combustion control, and the charge piping can usually be drilled and tapped for 1\/8 in NPT. The controller is not waterproof: mount it inside the driver's compartment, not in the engine bay.\u003c\/p\u003e\n\u003cp\u003eWater and methanol are the only supported fluids, and AEM strongly recommends never exceeding a 50% methanol concentration. Engine tuning is usually required to get the full power gain. We recommend installation by a qualified technician.\u003c\/p\u003e\n\u003ch2\u003eWarranty\u003c\/h2\u003e\n\u003cp\u003eAEM Electronics gives the original purchaser a 90-day warranty against defects in material and workmanship on its water\/methanol injection products, from the date of the original purchase, and will repair or replace a defective part. Normal wear, improper installation, misuse, reversed polarity wiring and cosmetic damage are not covered. Contact us with your order number if you need to make a claim.\u003c\/p\u003e\n\u003ch2\u003eFAQ\u003c\/h2\u003e\n\u003ch3\u003eHow much boost is it for?\u003c\/h3\u003e\n\u003cp\u003eForced-induction gasoline engines up to 35 psi boost; the controller's internal MAP sensor is rated up to 35 psi.\u003c\/p\u003e\n\u003ch3\u003eWhat is in the kit?\u003c\/h3\u003e\n\u003cp\u003eThe controller, a 1.15-gallon reservoir with conductive fluid-level sensor, a 200 psi pump, 250, 500 and 1000 cc\/min jets, 20 ft of nylon tubing and an LED status and low-fluid warning light, plus the wiring harness, boost pickup parts and mounting hardware.\u003c\/p\u003e\n\u003ch3\u003eWhat water\/methanol mix should I run?\u003c\/h3\u003e\n\u003cp\u003eAEM strongly recommends never exceeding a 50% methanol concentration.\u003c\/p\u003e\n\u003ch3\u003eIs shipping free?\u003c\/h3\u003e\n\u003cp\u003eFREE shipping on orders over $400 CAD (within Canada Only).\u003c\/p\u003e","brand":"AEM","offers":[{"title":"Default Title","offer_id":50922374430906,"sku":"30-3300","price":681.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0276\/1359\/3623\/files\/aem30-3300.jpg?v=1793669285","url":"https:\/\/n75motorsports.ca\/products\/aem-v3-water-methanol-injection-kit-35psi-boost-dependent-controller-w-1-15-gallon-tank","provider":"N75 MotorSports","version":"1.0","type":"link"}