AEM

AEM V3 Water/Methanol Injection Nozzle & Jet Kit - 250/500/1000cc, incl. T-Fitting & Hose

  • Sale
  • Regular price $115.00 USD
Shipping calculated at checkout.


IN STOCK

Fits: Universal: AEM (V2/V3) and compatible water/methanol injection systems. A direct upgrade or replacement for V2 injectors.

What this is

The AEM V3 Water/Methanol Injection Nozzle & Jet Kit is a complete injector assembly with a swirl-generator nozzle and three interchangeable jets flowing 250, 500 and 1000 cc/min. It includes a T-fitting and hose and serves as a direct upgrade or replacement for V2-style injectors, letting you fine-tune injection volume to your application.

AEM V3 water/methanol injection nozzle with a push-lock T-fitting and a coil of black nylon hose

Design

AEM's V3 injector uses Swirl Generator technology, which improves atomization for faster inlet air cooling and uses less fluid to keep the inlet air cool. The swirl generator, which AEM also calls the atomizing pintle, sets the flow through a fixed injector orifice, so changing the jet changes the flow. The nozzle has an internal check valve, and all of its parts are held in place by a single clip at the rear of the aluminum injector body, so it comes apart easily for cleaning. The 500 cc/min jet comes installed.

Features

  • V3 injector assembly with swirl generator
  • Three interchangeable jets: 250, 500 & 1000 cc/min
  • Includes T-fitting and hose
  • Direct upgrade/replacement for V2 injectors
  • In the kit (AEM): nozzle body, three atomizing pintles (jets), nozzle filter, 1/4 tube clip-type fitting, spring, check valve and check valve seal, retaining clip, 1/4 x 1/4 T-fitting and black 1/4 OD nylon hose

Coils of black nylon hose and small push-lock T-fitting pieces from the AEM nozzle and jet kit

Installation notes

AEM's instructions: mount the nozzle higher than the tank, so fluid cannot leak into the intake tract through gravity or siphoning. It must go before the throttle plate, after the MAF sensor if there is one, and after any intercoolers. In most instances, 6-8 in ahead of the throttle body gives an excellent combination of charge air cooling and combustion control. The charge piping can usually be drilled and tapped for 1/8 in NPT to mount the nozzle directly; on thin-walled tubing AEM suggests welding in a bung. Pick the jet for your power level with the nozzle selection chart in AEM's instructions.

AEM strongly recommends never exceeding a 50% methanol concentration in any AEM water/methanol system. We recommend installation by a qualified technician.

Close-up of the black AEM V3 water/methanol injection nozzle from the kit

Warranty

AEM Electronics gives the original purchaser a 90-day warranty against defects in material and workmanship on its water/methanol injection products, from the date of the original purchase, and will repair or replace a defective part. Normal wear, improper installation, misuse, reversed polarity wiring and cosmetic damage are not covered. Contact us with your order number if you need to make a claim.

FAQ

Which jet sizes are included?

Three interchangeable jets: 250, 500 and 1000 cc/min. The 500 cc/min jet comes installed.

Will it replace my older AEM injector?

Yes. It is a direct upgrade or replacement for V2-style injectors, and it suits AEM (V2/V3) and compatible water/methanol injection systems.

Does it come with a fitting and hose?

Yes. The kit includes a T-fitting and hose.

Is shipping free?

FREE shipping on orders over $400 CAD (within Canada Only).



Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)