JE Pistons

JE Pistons Forged Piston Set of 4 - Hyundai i30 N / Veloster N / Elantra N / Kona N 2.0T

  • Sale
  • Regular price $1,253.99 CAD
Shipping calculated at checkout.


ON ORDER at our distributor as of 5 November 2026

These are forged race pistons and they need machine work to fit. Budget for that work when you plan the build: these are not a part you drop into a standard engine over a weekend.

JE make this piston in more than one bore size. Tell us what your block measures, or what your machinist is planning, and we will make sure the right one comes.

Fits: Hyundai i30 N 2018 on, Veloster N 2019-2022, Elantra N 2022-2026 and Kona N 2022-2023, 2.0L Theta II turbo.

What this is

A JE Pistons forged piston set, four pistons: forged 2618 aluminium with JE's Forged Side Relief slipper skirt and a skirt coating, for the 2.0 litre Theta II turbo. It is supplied complete with wrist pins, wire locks and a matched JE Pro Seal ring set.

JE cuts this piston at a 30.00 mm compression height on a 22 mm pin for the stock 146 mm rod and 86.0 mm stroke, which are the factory figures for these engines. We sell it for these cars on that basis and on our own engine-building experience with them. JE's own catalogue lists this part under the Hyundai 2.0T Theta Genesis engine.

JE Pistons forged piston for the Hyundai 2.0T Theta II, showing the shallow dished crown with valve reliefs, ring grooves and black-coated slipper skirt

Design

Each piston is forged from 2618 T6 aluminium, with JE's Forged Side Relief slipper skirt and a skirt coating. The crown has an inverted spherical dish of minus 5.9 cc. The 22 mm (0.866 in) wrist pin is full-floating and is held by round wire locks, and the JE Pro Seal ring set runs a 1.0 mm top, 1.2 mm second and 2.8 mm oil ring. JE notes the design accepts turbo and nitrous.

Features

  • Set of 4 pistons
  • Compression height 30.00 mm (1.181 in)
  • Wrist pin 22 mm (0.866 in), full-floating, included
  • Round wire locks, included
  • Dish volume minus 5.9 cc, inverted spherical
  • Weight 305 g per piston
  • JE Pro Seal ring set included: 1.0 mm top, 1.2 mm second and 2.8 mm oil
  • 2618 T6 forged aluminium
  • Forged Side Relief slipper skirt with coating
  • Cut for the stock 146 mm rod and 86.0 mm stroke
  • JE notes the design accepts turbo and nitrous
  • Bore and clearance figures come on JE's own specification sheet with the set

Installation notes

These are forged race pistons and they need machine work to fit. The block is bored and honed to suit them and the piston-to-wall clearance is set to specification. JE supplies the full specification with the set, and that is what your machinist works to.

This is a full-floating pin. Check that your rod small ends are set up for one. If you are running the factory rods, have them measured first: they may need bushing or honing, and that is more machine work to budget for.

Running more than about 2 bar of boost? A reinforced piston pin is the accepted upgrade at that level and is a separate part. Tell us your target and we will specify it with you.

About compression ratio. We deliberately do not print one. The dish volume is a property of the piston and is given above, but the ratio your engine finishes at depends on your cylinder head and head gasket: any figure quoted on a box assumes a stock-thickness gasket, so a thicker one changes it. Tell us your build and we will work it out with you.

Have the piston-to-valve clearance checked at assembly. These engines are direct injected and tight. Clay-check it on the bench before the engine goes together.

Ask us for a lead time before you book machine work. Not sure this suits your car? Ask us before ordering: we would rather check the fitment than process a return.

Warranty

Contact us with your order number if you have any problem with your part.

FAQ

Do these drop into a standard engine?

No. They are forged race pistons and need machine work: the block is bored and honed to suit them and the piston-to-wall clearance is set to the specification JE supplies with the set.

Are the rings and pins included?

Yes. The set comes with wrist pins, round wire locks and a matched JE Pro Seal ring set.

What compression ratio will I get?

We deliberately do not print one. It depends on your cylinder head and head gasket. Tell us your build and we will work it out with you.

When can I get it?

It is ON ORDER at our distributor as of 5 November 2026. Ask us for a lead time before you book machine work.



Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)