K&N Filters

K&N Cold Air Intake - Kia Stinger

  • Sale
  • Regular price $479.00 USD
Shipping calculated at checkout.


ON ORDER: available to order in

Fits: 2018-20 Kia Stinger with the 2.0L turbo (L4-2.0L Turbo), per K&N's installation sheet, which also lists the 2019-20 Genesis G70 2.0L turbo. Fitment per the Marcor Automotive catalogue: Kia Stinger.

What this is

K&N cold air intake system for the Kia Stinger. K&N lists it for the 2.0L turbo four-cylinder only. It replaces the factory air filter housing with a K&N heat shield, a short aluminum intake tube and a K&N air filter.

On K&N's dyno, a 2018 Kia Stinger 2.0L turbo gained 5.4 hp at 5799 rpm and 11.3 lb-ft at 4233 rpm with this intake. K&N notes that gains are based on a specific or similar vehicle test and that results will vary.

K&N cold air intake kit for the Kia Stinger 2.0L turbo, with silver intake tube, black heat shield and red cone air filter

Design

The factory turbo inlet tube is kept: it goes back in with a new coupler (3-5/8 in ID x 1-3/4 in long), clocked slightly left of its factory position. A 3.5 in OD x 7.5 in long aluminum tube joins it to a second coupler (3-1/2 in ID x 2 in long) on a 6 in filter adapter in the heat shield, and the K&N air filter (6 in flange, 7-1/2 in base) clamps onto the adapter. The heat shield mounts with a steel L bracket and is finished with edge trim, and two vent fittings in the tube take the factory vent lines.

Features

  • K&N dyno result on a 2018 Kia Stinger 2.0L turbo: +5.4 hp @ 5799 rpm and +11.3 lb-ft @ 4233 rpm (results will vary)
  • 3.5 in OD x 7.5 in long aluminum intake tube
  • K&N air filter on a 6 in universal adapter
  • Heat shield with steel L bracket and edge trim
  • Two couplers, hose clamps and mounting hardware included
  • Two vent fittings for the factory vent lines
  • Filter cleaning every 100,000 miles, more often in dusty or off-road use, with a visual check every 25,000 miles

Installation notes

Following K&N's installation sheet, the passenger side chassis brace, the upper and lower air filter housing, the factory intake tube and the turbo inlet tube come out. The turbo inlet tube goes back in with the new coupler, clocked slightly left of its factory position, and the heat shield and intake tube go in as a unit before the chassis brace is refitted. Some trimming of the edge trim is necessary. The plastic NPT vent fittings are easy to cross thread: fit them hand tight, then two complete turns with a wrench. Tools needed: ratchet, extension, 10mm socket, 10mm wrench and flat blade screwdriver. K&N recommends keeping the factory air intake, and says its intake systems should be checked periodically for alignment, clearance and tight connections; failure to follow the instructions or proper maintenance may void the warranty. To clean and re-oil the filter, use K&N's Recharger service kit. We recommend installation by a qualified technician.

Warranty

K&N gives its No-Hassle Lifetime Limited Warranty on its air intakes: it lasts for the lifetime of the product and covers the original purchaser only, and it is not transferable. Damage from racing, competition or any off-road use is not covered. Contact us with your order number if you need to make a claim.

FAQ

Which Stinger does it fit?

K&N lists the 2018-20 Kia Stinger with the 2.0L turbo four-cylinder, and the 2019-20 Genesis G70 2.0L turbo. It is not listed for the other Stinger engines.

How much power does it add?

On K&N's dyno, a 2018 Stinger 2.0L turbo gained 5.4 hp at 5799 rpm and 11.3 lb-ft at 4233 rpm. K&N notes that results will vary.

Does it reuse any factory parts?

Yes. The factory turbo inlet tube goes back in with the new coupler, and K&N recommends keeping the factory air intake.

Is it in stock?

It is on order and available to order in.



Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)