K&N Filters

K&N Charge Pipe Kit - Kia Stinger

  • Sale
  • Regular price $420.00 USD
Shipping calculated at checkout.


ON ORDER: available to order in

Fits: 2019-21 Kia Stinger with the 3.3L V6 (V6-3.3L), per K&N's installation sheet. Fitment per the Marcor Automotive catalogue: Kia Stinger.

What this is

K&N aluminium charge pipe kit for the Kia Stinger. It replaces the factory charge tube that runs from the intercooler coupler to the throttle body on the 3.3L V6.

On K&N's dyno, a 2021 Kia Stinger 3.3L turbo gained 11.9 hp at 4506 rpm and 17.76 lb-ft at 3347 rpm with this charge tube kit. K&N notes that gains are based on a specific or similar vehicle test and that results will vary.

K&N charge pipe for the Kia Stinger 3.3L V6, a silver tube with the K&N logo, coupler and T-bolt clamp

Design

A 3 in OD, 34 in long aluminium charge tube. It slides into the factory intercooler coupler at one end and joins the throttle body through a new 3.25 in to 3 in ID x 3 in long coupler at the other, with T-bolt hose clamps. The factory pressure sensor and vacuum switch move over to the K&N tube with their factory bolts, the factory vacuum line connects to a fitting in the tube, and the supplied stainless steel 1/8 in NPT plug closes the accessory port.

Features

  • K&N dyno result on a 2021 Kia Stinger 3.3L turbo: +11.9 hp @ 4506 rpm and +17.76 lb-ft @ 3347 rpm (results will vary)
  • Aluminium charge tube, 3 in OD x 34 in long
  • Coupler hose, 3.25 in to 3 in ID x 3 in long, with T-bolt hose clamps
  • Takes the factory pressure sensor, vacuum switch and vacuum line
  • Kit contents: charge tube, coupler hose, two T-bolt hose clamps, temp sensor adapter and stainless steel 1/8 in NPT plug

Installation notes

Following K&N's installation sheet, the passenger side strut tower brace, the air filter housing and the intake tube come out to reach the factory charge tube. The vacuum switch, vacuum line and pressure sensor are disconnected, the charge tube is unbolted from the engine and released from the intercooler coupler and the throttle body, and the pressure sensor and vacuum switch are refitted to the K&N tube with their factory bolts. The vacuum fitting uses 1/4 in NPT threads: do not over tighten it, as the fitting may fracture, and some threads may stay exposed once it is properly installed. Check the tube's position before tightening all the hose clamps, then refit the intake tube, the air filter housing and the strut tower brace. Tools needed: ratchet, extension, 12mm, 10mm and 8mm sockets, 11mm deep socket, pliers and 5mm Allen key.

K&N's sheet says its high flow systems should be checked periodically for alignment, clearance and tight connections, and that failure to follow the instructions or proper maintenance may void the warranty. We recommend installation by a qualified technician.

Warranty

K&N gives its No-Hassle Lifetime Limited Warranty on its charge pipe kits: it lasts for the lifetime of the product and covers the original purchaser only, and it is not transferable. Damage from racing, competition or any off-road use is not covered. Contact us with your order number if you need to make a claim.

FAQ

Which Stinger does it fit?

K&N lists the 2019-21 Kia Stinger with the 3.3L V6.

How much power does it add?

On K&N's dyno, a 2021 Stinger 3.3L turbo gained 11.9 hp at 4506 rpm and 17.76 lb-ft at 3347 rpm. K&N notes that results will vary.

Do my factory sensors carry over?

Yes. The factory pressure sensor and vacuum switch move to the K&N charge tube with their factory bolts, and the factory vacuum line connects to a fitting in the tube.

Is it in stock?

It is on order and available to order in.



Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)